HOW TO REPLACE A DISHWASHER HANDLE HOW TO

While re-tightening into place, you can operate the door closed while watching carefully to see where the latch hits the plate so you can adjust as needed. If it's bent, it may have to be removed, straightened out with the proper tools and reinstalled, or it may even need to be replaced. To test, visually appraise it for any abnormalities if the strike plate is bent in anyway, is loose, or out of alignment, it will need to be readjusted to its original shape and location within the door frame opening. If the strike plate is out of alignment, the door will not close properly. The strike plate is located on the dishwasher itself and is the part that the dishwasher door latch grabs onto to when it's closed. Unfortunately, you do need to take the dishwasher out of the cabinet since the rollers run along the side of the machine and the spring is on the back. While spraying, use a rag or your fingers to move the latch back and forth so the lubricant gets into all of the moving parts. So long as you get the right replacement part for your brand and model, you should be able to replace either of these parts in as little as 20-30 minutes. This can be found easily at your local hardware store. A spray of industrial cleaner such as nut or bolt loosener would probably get the lever moving easily again, after which you should give an additional spray with a good penetrating lubricant.

On some models, the latch will get its rotating movement from a pivot pin in an area where the dirt can accumulate and impede the movement or interfere with it. So, if there's anything lodged anywhere in there, it has to be cleaned out and then tested again to see if your problem is still there. If it's large enough or if enough debris is present, it will keep the door from closing properly and stop the dishwasher from working altogether. Sometimes food particles or other foreign debris can become wedged inside, making it hard to open or close. If the problem is the dishwasher door latch, the next step is to closely inspect it. If any noise comes on you can assume electrical activity within and proceed at checking the latch itself as being the source of the problem. By depressing the switch with an object of similar size and shape, if the dishwasher does not come on, the problem is very likely to be the safety switch and you will need to be replaced. The switch will be inside an opening at the top of the door opening where the latch lines up when closing the door. To test the switch, you need to find its location by looking at the type of latch used and where it's placed on the door. If your dishwasher is malfunctioning and youвЂ™re not sure what part is causing the issue, please contact usВ today, and weвЂ™ll be happy to help you.The first thing you need to do when working at a dishwasher door is to TURN OFF THE WATER supply, as the water will spray out the minute it is started. Then, secure the console by rethreading the screws on the dishwasherвЂ™s back panel. Once the cable is reattached, rotate the control panel up and push it onto the front of your dishwasher. Take the control panel back to the dishwasher and reconnect the ribbon cable.Snap the new handle actuator into the door handle assembly, and then put the assembly back into the control panel.Before throwing out the broken component, take off the actuator spring, and slide it on the new part. Now remove the damaged door handle actuator from the door handle assembly.Then, take out the door handle assembly by releasing the locking tabs securing it to the control panel.

Next, remove the metal support bracket from the top of the panel. Place the control panel face down on a flat surface.Rest the panel on the front of the appliance, and disconnect the ribbon cable that runs between the console and the dishwasher by disengaging its locking tab with a flathead screwdriver. Partially close the door, and then, remove the control panel from the dishwasher.Open your dishwasher door and unthread the screws that secure the control panel to the front of the dishwasher.

HOW TO REPLACE A DISHWASHER HANDLE HOW TO

How to Replace the Handle Actuator in Your GE Dishwasher

If at some point you donвЂ™t feel comfortable continuing the repair, please stop what youвЂ™re doing and contact an appliance repair technician to complete the job.

In order to keep your eyes and hands protected you should wear work gloves and safety goggles while fixing your dishwasher.

Before you start repairing your dishwasher, unplug the appliance and turn off its water supply.

Luckily, replacing the latch is a quick and easy repair that should take you no more than an hour or two. A damaged actuator may stop your dishwasher door from opening. When you lift the door handle on your GE dishwasher model GSD6600GBB, the handle actuator releases the door latch.

How to replace a dishwasher handle